Автомобиль в мастерской When working on a vehicle in the workshop always make sure that: Where practicable, the parking brake is applied and the wheels are securely chocked to prevent the vehicle moving forwards or backwards. Whenever possible, the ignition key is removed...
Аккумуляторная батарея Предостережение: It is essential that a period of 10 minutes elapses after the battery is disconnected before any work is undertaken on any part of the SRS system. Внимание: Prior to carrying out any procedures which involve disconnecting/ or...
Запуск двигателя автомобиля Внимание: While it is not recommended that a vehicle is jump started, it is recognized that this may occasionally be the only practical way to mobilize a vehicle. Reference should be made to the following and also to the Electrical Section of this...
Буксировка автомобиля Предостережение: When towing is necessary, reference must be made to the Jacking, Lifting and Towing Section of this Manual. When the vehicle is being towed the ignition switch must be in position II (steering lock released and warning lights...
Общие указания по установке Component removal Whenever possible, clean components and the surrounding area before removal. Blank off openings exposed by component removal. Following disconnection, seal fuel, oil or hydraulic lines immediately using suitable blanking plugs or...
Общий осмотр компонентов All components should be inspected for wear or damage before reassembling. Always ensure that component to be inspected is clean and free from oil or grease. When a component is to be checked dimensionally against design specified values, use the...
Стопорные приспособления Always replace locking devices with one of the same design and of the correct size. Tab washers . Always release locking tabs before loosening fixings, do not re-use tab washers. Locknuts . Always use a backing spanner when loosening and tightening...
Обозначения болтов и гаек An ISO metric bolt or screw made of steel and larger than 6 mm in diameter can be identified by either of the symbols ISO M or M embossed or indented on top of the bolt head. In addition to marks identifying the manufacturer, the top of the bolt...
Шариковые и роликовые подшипники When removing and installing bearings, ensure that the following practices are observed to ensure component serviceability: Внимание: Service tools have been developed for removing the majority of bearings; these must always be used where specified....
Гидропривод тормозной системы Brake Pads and Linings Always fit the correct grade and specification of brake pads and linings. When replacing these items, always replace as complete axle sets. Brake Hydraulics Always observe the following recommendations when working on the...
Гибкие трубопроводы и шланги When removing or installing flexible hydraulic pipes and hoses, ensure that the following procedures are observed to ensure component serviceability: Prior to removal, clean area around hose or pipe end which is to be disconnected. Obtain...
Шланги и хомуты топливной системы Fuel system hoses Some fuel hoses are made up of two laminations, an armoured rubber outer sleeve and an inner viton core. Whenever a hose is removed, ensure that the inner bore is inspected to check that the viton lining has not become separated...
Ориентация и подключение шлангов Correct orientation of cooling system hoses is important to ensure that hoses do not become fatigued or damaged through contact with adjacent components. Where orientation marks are provided on the hose and corresponding component, the marks must be...
Меры предосторожности при работе с электрооборудованием General The following guidelines are intended to ensure the safety of the operator whilst preventing damage to the electrical and electronic components of this vehicle. Equipment Prior to commencing any test procedure on the vehicle, ensure that the...
Меры предосторожности при работе с топливом The following information lists basic precautions which must be observed if fuel is to be handled safely. It also outlines other areas of risk which must not be ignored. As this information is issued for basic guidance only, consult your local Fire...
Масляные уплотнения Always renew oil seals which have been removed either as an individual component or as part of an assembly. Never use a seal which has been improperly stored or handled. Take great care when removing old seals that the sealing surfaces and seal...
Меры безопасности при работе с системой защиты людей (SRS) Предостережение: Do not fit rear facing child seats in the front passenger seat. The SRS contains components which are potentially hazardous to service personnel if not handled correctly. The following guidelines and precautions are intended to...
Осмотр датчиков удара After any degree of side or frontal body damage, inspect the impact crash sensors. Replace a crash sensor if there is any sign of damage. Внимание: Take extra care when painting or carrying out bodywork repairs in the vicinity of the crash sensors....
Активация подушек и преднатяжителей ремней безопасности Предостережение: During deployment parts of the airbag module become hot enough to burn you. Wait 30 minutes after deployment before touching the airbag module. Deployment procedures and precautions as detailed in this manual should be strictly...
Замена компонентов системы SRS Внимание: The Restraints Control Module (RCM) will log a crash fault after every impact which is severe enough to cause airbag deployment. It is possible to have three crashes/impacts logged after one event where, for example, a front, side and...
Срабатывание фронтальной подушки безопасности Внимание: If the front airbags are deployed, the following components must be replaced: Driver airbag module Passenger airbag module Fly leads (where applicable) connecting front airbag modules to SRS harness Front seat belt buckle pre-tensioner...
Срабатывание боковой подушки безопасности Внимание: If the side curtain air bags are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred: Side curtain airbag Any side impact sensors that have been physically damaged or if a fault...
Модули шторок безопасности Внимание: If the head airbag modules are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred: Head airbag modules Link lead between airbag gas generator and restraints control module (RCM)...
Удар автомобиля сзади Внимание: If the seat belt pre-tensioners are deployed during a rear impact, the following components must be replaced: Seat belt pre-tensioners Front and rear seat belt retractors used during the impact Restraints Control Module (RCM) if the three...
Предосторожности при работе с системой кондиционирования The A/C system contains fluids and components which could be potentially hazardous to the service engineer or the environment if not serviced and handled correctly. The following guidelines are intended to alert the service engineer to potential...
Дорожное испытание автомобиля — введение Дорожное испытание или испытание на роликовом стенде выполняется по различным причинам. Далее рассматривается подробное описание предварительных проверок посредством запуска и остановки двигателя, проверок перед дорожным испытанием, проверок в...
Запуск двигателя Примечание: Начав движение с холодным двигателем, на протяжении первых 1,5 км не нажимайте на педаль акселератора более чем на половину хода, пока автомобиль не достигнет скорости не менее 25 км/ч. Пока двигатель не прогрет, никогда не допускайте...
Проведение дорожного испытания Внимание: Начав дорожное испытание и двигаясь на низкой скорости, проверьте работу тормозной системы, не прекращая испытания. Если тормоза срабатывают только с одной из сторон или неисправность проявляется иным образом, не продолжайте дорожное...
Проверка тормозной системы Избегайте проверки тормозной системы на дорогах с интенсивным движением, где это может привести к затруднению движения или опасности для других участников движения. Внимание: Если на автомобиле установлены новые тормозные колодки...
Испытание на роликовом стенде Роликовый стенд для четырех колес Предостережение: Запрещается применять ножной или стояночный тормоз, когда ролики приводят в движение колеса. Убедитесь, что после отсоединения карданные валы надежно закреплены и все элементы валов остановлены....